Skid Steer Maintenance Checklist: Daily and Weekly Checks

A skid steer or compact track loader (CTL) will put up with a lot, but it doesn’t forgive skipped checks. Expensive problems usually start small: a low fluid level, a dry pin, mud packed in the undercarriage, or a machine worked hard before it’s warm. A few minutes of checks at the start of the day is how you catch them.

This checklist uses the John Deere 325G operator’s manual as the worked example, because the 325G is one of the track loaders in our fleet. Other brands follow the same idea, but intervals, fluids and procedures differ by model. Your operator’s manual is always the authority.

On a Lybroco rental? The walk-around and fluid-level checks below are a good habit on any machine. If something looks wrong, such as a leak, a low level that keeps dropping, a warning light or a damaged track or tire, stop and call us at 1.800.674.1018 before you keep working. Please don’t adjust, repair or service a rental unit yourself.

Daily checks: before you start (every 10 hours or daily)

Deere lists four items under “Every 10 Hours or Daily” on the 325G, plus a walk-around inspection before starting [1].

1. Walk around the machine

  • Hydraulics: look for leaks, missing or loose clamps, kinked hoses, and hoses rubbing on each other or on the machine [1].
  • Fuel system: check for leaks, loose clamps and kinked hoses, and drain water and sediment from the fuel filters [1].
  • Electrical: look for worn or frayed wires and loose or corroded connections [1].
  • Hardware, sheet metal and tracks: check for bent, broken, loose or missing parts [1].
  • Protective devices: inspect guards, shields, the ROPS and the seat belt [1].
  • Rear grille and exhaust stack: make sure nothing is blocking them [1].
  • Fuel level: top up with the fuel the manual calls for [1].
  • Bystanders: walk around once more to make sure nobody is near the machine before you start [1].

2. Check engine oil

Park on level ground. The most accurate reading is with a cold engine, before the day’s first start. If the engine has been running, wait 10 minutes for the oil to drain back before you check [1]. Don’t run the engine with the oil below the ADD mark [1].

Milky-looking oil on the dipstick can come from moisture in the crankcase ventilation. Deere says to check the coolant level to rule out coolant getting into the oil, and to take an oil sample if you’re still unsure [1].

3. Check hydraulic oil

Check it cold, on smooth level ground, with the boom down and the boom and bucket cylinders fully retracted. The level should sit between the arrow marks on the gauge [1]. Keep dirt out when you add oil, and don’t overfill: an overfilled reservoir has no room for expansion and can leak past the breather or fill cap [1].

4. Check coolant

Only open the cap when it’s cool enough to touch with bare hands, and loosen it slowly to release pressure [1]. Cold coolant should sit above the MIN COLD line and below the MAX COLD line on the surge tank [1].

5. Grease the boom and linkage

On the 325G, Deere calls for 1 to 2 shots of grease at each boom linkage point, cylinder pivot point and Quik-Tatch linkage point on both sides, every 10 hours or daily [1]. In severe conditions, the coupler points may need grease more often [1].

6. Clean out the undercarriage

Packed mud, clay or frozen material tightens the track and speeds up wear on pins, bushings and sprockets [1][2]. In cold weather, Deere says to clean the undercarriage at the end of the day so material doesn’t freeze overnight [1]. Don’t try to break frozen material loose by driving the machine [2].

Weekly checks (every 50 hours)

  • Track sag: Deere says to monitor track sag weekly or as needed, and check track tension every 50 hours [1]. On the 325G, sag is measured with the front of the machine raised on the bucket, from the bottom of the third roller from the rear to the top of the track: 25 to 38 mm (1.00 to 1.50 in) [1]. Other models have different figures and methods. Our track guide walks through it.
  • Dust unloader valve: squeeze it to clear dust from the air cleaner and replace it if it’s hardened or damaged. In very dusty conditions, Deere suggests squeezing it every 2 hours [1].
  • First 50 hours only: the 325G calls for draining and refilling the hydrostatic planetary gear case oil at the initial 50-hour service [1].

Wheeled skid steer? Machines on tires, such as our John Deere 318G and Case SR240B, skip the track checks. Check the tires for cuts and damage and follow the manual for tire pressure and any other weekly items.

Longer intervals (shop items)

On the 325G, the longer service items include an engine oil sample at 250 hours, engine oil and filter, fuel filters and hydraulic filter at 500 hours, and hydraulic oil and gear case oil changes at 1,000 hours [1]. These are shop jobs. If you own your machine, follow the full chart in your manual. If you’re renting from us, they aren’t your job.

Edmonton winter tips

  • Plug it in. Deere recommends the engine block heater below -15 °C (5 °F). Plug it in for at least 4 hours between -15 °C and -25 °C, and at least 10 hours below -25 °C (-13 °F) [1]. Use a heavy-duty, grounded cord [1].
  • Warm it up before you work it. Below 0 °C (32 °F), Deere says to run the engine at slow idle for 10 minutes before operating the controls, then work at lighter loads and speeds until it reaches normal temperature [1].
  • No starting fluid. Deere says not to use ether or any other starting fluid on these engines. If it doesn’t start within 60 seconds of cranking, stop and let the starter cool for 65 seconds before trying again [1].
  • Park smart. Leave the machine on dry, flat ground where the tracks won’t freeze in overnight [2].

Printable daily checklist

  • ☐ Walk-around: leaks, hoses, clamps, wiring, loose or missing parts
  • ☐ Guards, ROPS and seat belt
  • ☐ Rear grille and exhaust clear
  • ☐ Engine oil level (cold, before start)
  • ☐ Hydraulic oil level (cold, boom down)
  • ☐ Coolant above MIN COLD and below MAX COLD
  • ☐ Grease boom, cylinder pivots and coupler
  • ☐ Fuel topped up
  • ☐ Undercarriage cleaned out (end of day in winter)
  • ☐ Weekly: track sag or tire condition, dust unloader valve

Need a skid steer or track loader in Edmonton?

See our skid steers and track loaders, book online, or ask about skid steer training. Call 1.800.674.1018. Lybroco Rentals, 1810 Yellowhead Trail NE, Edmonton AB T6S 1B4, open Monday to Friday, 8 to 5.

Sources

  1. John Deere, 325G Compact Track Loader Operator’s Manual, OMT396974X19: Service Intervals (3-2-9), Inspect Machine Daily Before Starting (2-2-1), Every 10 Hours or Daily (3-4-1 to 3-4-4), Initial Service 50 Hours (3-5-1), Every 50 Hours (3-6-1 to 3-6-3), Starting the Engine and Engine Block Heater (2-2), Rubber Track Usage (2-4).
  2. Camso, Track Installation Guide / Operational Guidelines: Compact Track Loaders (V7, 2023) and “Operation, maintenance and storage tips for your construction tracks this winter.”