People search “change skid steer tracks,” but rubber tracks belong on a compact track loader (CTL). At Lybroco Rentals in Edmonton, that means our John Deere 317G, 325G and 333G and Case TR- and TV-series loaders. Our JD 318G and Case SR240B are wheeled skid steers with no track to swap.
This guide covers how a rubber CTL track comes off and goes back on, how to set sag, and the mistakes that wreck new tracks early. Every number comes from an OEM manual or published source listed at the bottom. Where we couldn’t find one for your model, we say so, and your operator’s manual is the authority.
Renting from us? On a Lybroco rental, call us first at 1.800.674.1018. Please don’t change tracks or adjust track tension on a rental unit. This guide is for machine owners, and for knowing what to watch for on the job.
How a CTL track tensioner works
On most CTLs, tension comes from a grease cylinder that pushes the front idler forward. Pump grease in and the idler pushes the track tight; let grease out and it retracts [8]. On Deere G-series loaders, a cover plate on the track frame hides a grease fitting for adding grease and a separate track adjuster valve for releasing it [1].
The grease in that cylinder is under high pressure. Deere says to loosen the valve slowly and not too far, and never to loosen the grease fitting to release grease [1]. Some aftermarket guides say to remove the fitting instead [5], so follow your machine’s manual. Case’s Tier 3 B-Series manual says to turn the relief fitting counterclockwise with a 19 mm tool [4].
Tools you’ll need
- Grease gun with the grease your manual specifies. Case lists NLGI 2 multi-purpose grease [4].
- Sockets and wrenches. Case’s Tier 3 B-Series manual calls for 13 mm for the access cover and 19 mm for the relief fitting [4].
- Pry bar. Camso’s guide lists a 30-inch flat-end bar [5].
- A lifting device rated for the machine, plus blocks or stands. Deere’s repair manual lists the 325G at about 4,381 kg (9,658 lb) and the 333G at about 5,715 kg (12,600 lb) for this step [2][3].
- A way to handle the track. A 325G track weighs about 214 kg (471 lb), and a 333G track about 249 kg (549 lb) [2][3].
- Three steel pipes 38–51 mm (1.5–2.0 in) in diameter. This is Deere’s method for lifting the track off the front idler [2].
- A bucket or drip pan for the old grease, and a tape measure or straightedge for checking sag.
Step by step: changing a CTL track
This is the John Deere 325G/333G repair-manual sequence [2][3]. Other brands are similar, but check your manual.
- Remove the attachment and park on flat, level ground [2][5].
- Raise and block the machine to OEM procedure. Deere’s method: raise the boom and engage the boom lock, stop the engine and relieve hydraulic pressure. Lift at the front centre of the machine base, set blocks or stands under the front corners, then repeat at the rear. Confirm the machine is stable [2].
- Remove the track adjuster cover plate from the track frame [2].
- Release the tension. Slowly loosen the adjuster valve 1–2 turns and let grease discharge until the track sags completely [2]. Keep your hands and face away from the valve: grease escaping under pressure can penetrate skin [1]. Catch the grease and dispose of it properly.
- Retract the idler. As the grease leaves, the front idler should move back. If it hangs up, Camso’s guide says to lever the idler back to full retraction with a pry bar or come-along [5].
- Lift the track off the front idler. Lay the three steel pipes evenly spaced on the track, below the track frame. Start the engine and run it at slow idle. With bystanders well clear, slowly rotate the drive sprocket in reverse until the pipes lift the track off the front idler. Stop the engine [2].
- Walk the old track off. Using a suitable lifting device, pry and slide the track away from the front idler and track frame [2].
- Inspect while it’s open. Clean and check rollers, idlers and sprocket against the checklist below [2][5].
- Fit the new track. Put it on the drive sprocket teeth and rear idler first, then slip the front end over the front idler [2]. Camso adds that the track should sit aligned under the rollers [5].
- Seat it. With the pipes on the track again, rotate the sprocket in reverse at slow idle to guide the track onto the front idler. Stop, pry the centre guide lugs into line over the idler, then rotate again and pull the pipes as they come off [2].
- Confirm engagement. The track must be fully engaged on the sprocket, rear idler and front idler before you tension it or run the machine [2].
- Re-tension, refit the cover and lower the machine. Add grease through the fitting to take up the slack, reinstall the cover plate, raise the machine off the blocks and lower the boom [2]. Then set the final sag with the measuring method in the next section. Deere says sag can only be measured safely and accurately with the front raised on the bucket, not with the machine on stands [1].
- Recheck after break-in. Case’s Tier 3 manual says to check tension after the first 10 hours on new tracks, then every 50 hours after that [4].
How to measure track sag
Deere’s 325G method [1]:
- Install a bucket that isn’t broken or worn out. Raise the boom and roll the bucket to full dump.
- Lower the boom until the front lifts about 20 cm (8 in) off the ground. Engage the park brake, shut down and confirm the machine is stable. Stay alert for the machine settling from hydraulic leakage, and don’t use the bucket as a step [1].
- Clear any gravel or mud packed between the sprocket and track.
- Measure from the bottom of the third roller from the rear to the top of the track. Spec on the 325G is 25–38 mm (1.00–1.50 in). To tighten, add grease at the fitting; to loosen, open the adjuster valve 1–2 turns, then close it when sag is right [1].
- Repeat on the other side. Deere lists uneven left and right sag as a cause of a machine that mistracks [1].
Case’s Tier 3 B-Series manual works differently. It covers the TR270B, TR320B and TV380B from PIN NJM453496. Raise and block the machine until the tracks are about 50 mm (2.0 in) off the surface, then measure from the bottom of the centre roller to the top of the lower track. Allowable sag is 12–19 mm (0.5–0.75 in) [4]. Tier 4B B-Series machines have their own manual, and we haven’t checked its figure. Check the PIN range on your manual’s cover before using this number.
For the 317G, 333G, 333 P-Tier and Tier 4B Case machines, including the Case loaders in our fleet, see your operator’s manual. We haven’t verified a published sag figure for those models, and you shouldn’t borrow one from a different machine.
Common ways tracks fail early
- Wrong tension. Deere’s news site calls it the main cause of track failure [7]. Loose tracks wander and de-track, especially with side-slope work or spin turns. Tight tracks cost power and wear the undercarriage [1][8].
- Packing. Mud, clay or frozen material in the undercarriage tightens the track and speeds up pin, bushing and sprocket wear [1][5].
- New track on a worn sprocket. Tracks and undercarriage parts are designed to wear together. Putting a new track on worn sprockets, rollers or idlers “will drastically reduce your overall track life” [5].
- Counter-rotating on pavement. Spin and pivot turns speed up wear and raise the risk of de-tracking. On hard surfaces, make wider turns or three-point turns [1][7][8]. Some operators sprinkle sand or dirt on pavement to cut wear [7].
- Demolition debris. Broken stone, rebar, scrap iron and recycled material wear tracks early, and rocky ground causes cuts and chipping [1][5][8]. Avoid the “three Rs”: rocks, roots and rebar [8].
- Curbs at an angle. Cross curbs head-on. Hitting them at an angle can tear the track edge [8].
Signs it’s time to replace the track
- [ ] Lug height below minimum. Deere’s 325G and 333G repair manuals set a minimum of 5 mm (0.2 in) [2][3].
- [ ] Cracks in or between lugs deeper than 3 mm (0.1 in), longer than 30 mm (1.2 in), or reaching the steel core [2][3].
- [ ] Exposed steel core or cords, or the core separating anywhere, including on the roller side [2][3].
- [ ] Cuts running across the track. Cuts that run lengthwise can often run for a while. Cross cuts often end in complete failure. Severed cords mean failure is probably close [7].
- [ ] Sprocket wear. Check the tops of the sprocket teeth. Sandy ground speeds this up [1]. If the sprocket is worn, plan to replace it with the track [5].
- [ ] Not a failure: fine wear lines in dirt work are normal, as long as rubber isn’t chunking out [1].
Track life varies a lot. Equipment World quotes a range of 400 to 2,000 hours, with the average around 1,200 to 1,600 [8].
Edmonton cold-weather tips
Camso treats anything below 7 °C (44 °F) as winter conditions for tracks. For Edmonton, that covers a big part of the year [6].
- Clean before you park. Deere’s manual says to clean out the undercarriage at the end of the day in cold weather, so material doesn’t freeze and put excessive loads on the machine’s systems [1]. Camso says the same: clean daily [5][6].
- Don’t drive it loose. Remove frozen material before moving the machine. Camso says never to clear it by driving [5].
- Pick your parking spot. Slop can freeze solid overnight. Park on dry, flat ground where the tracks won’t freeze in or drift over [6].
- Go easy on stiff rubber. Cold rubber is more brittle. Avoid spinning and jagged ice or frozen debris [6].
- Recheck tension when conditions change. Deere notes tracks may need adjusting several times a day as soil and moisture change, and says to adjust in actual working conditions [1]. As a general rule of thumb (not an OEM spec), measure again after a big freeze-thaw swing.
FAQ
How often should I check CTL track tension?
Deere: every 50 hours, and watch sag weekly or as needed [1]. Case: 10 hours after new tracks, then every 50 [4]. Equipment World suggests about every 10 hours in practice [8].
Can I change only one track?
Nothing in the manuals we reviewed forbids it. Set both sides to spec afterward, because uneven sag causes mistracking [1], and check that side’s sprocket [5].
Can I use aftermarket tracks?
Yes, but there’s no universal track. Sprocket, roller and flange designs vary by brand and model, so match the track to your exact machine [8].
Do wheeled skid steers like the 318G or SR240B get tracks?
No. They run on tires. Over-the-tire tracks exist as a separate product [6], but if the job needs tracks, rent a CTL.
Need a track loader in Edmonton?
Browse our skid steers and track loaders or call 1.800.674.1018. Lybroco Rentals, 1810 Yellowhead Trail NE, Edmonton AB T6S 1B4, Monday to Friday, 8 to 5; closed Saturdays except by appointment.
Sources (accessed 2026-10-22)
- John Deere, 325G Compact Track Loader Operator’s Manual, OMT396974X19 Issue B5 (PIN J328658—). Sections: Check Track Tension (Maintenance—Every 50 Hours, 3-6-2/3-6-3); Rubber Track Usage AVOID/DO (2-4-1/2-4-2); Sprocket Teeth Wear (2-4-3); Normal Track Wear (2-4-4); Track Sag General Information (4-1-22); Troubleshooting—Machine Mistracks. Copy hosted at https://hartoil.com/uploads/JD325G%20Manual.PDF
- John Deere, 325G Compact Track Loader Repair Technical Manual, TM14295X19 (28DEC21). Group 0130 Track System (Measure Rubber Track Height; Track Remove and Install) and Group 1740 (Raising and Blocking Machine). Owner-supplied copy:
/workspace/lybroco/OEM_DOCS/manuals/JohnDeere_TM14295X19_325G_CTL_Repair_28DEC21.pdf. Not public; Deere sells it through dealers / techpubs.deere.com. - John Deere, 331G and 333G Compact Track Loader Repair Technical Manual, TM14064X19 (07OCT22). Group 0130 Track System and Raising and Blocking Machine. Owner-supplied copy:
/workspace/lybroco/OEM_DOCS/manuals/JohnDeere_TM14064X19_331G_333G_CTL_Repair_07OCT22.pdf. - CASE Construction Equipment, B Series Skid Steer Loader / Compact Track Loader Operator’s Manual (Tier 3), part no. 90416920, 2nd ed., Feb 2021 (TR270B, TR320B, TV380B). Track tension check and adjustment, Initial 10 hours and Every 50 hours (pp. 7-23, 7-41). https://www.manualslib.com/manual/4102441/Case-Construction-B-Series.html?page=195
- Camso, Track Installation Guide / Operational Guidelines — Compact Track Loaders (V7, 2023-02-02). https://camso.co/content/files/products/CO/2212_CO_Tracks_CTL_InstallationGuide%C2%B4%C3%87%C3%B3OperationalGuidelines_Letter_EN_V7_2023-02-02-193729_vmyr.pdf
- Camso, “Operation, maintenance and storage tips for your construction tracks this winter.” https://camso.co/en/blog/best-practices/operation-maintenance-and-storage-tips-for-your-construction-tracks-this-winter/
- John Deere News, “Tech Tips: Managing Track Wear” (Sept 12, 2019). https://www.news-jd.com/tech-tips-managing-track-wear/
- Tom Jackson, “How to get the most hours out of your CTL tracks,” Equipment World (Jul 12, 2019; updated Sep 22, 2026). https://www.equipmentworld.com/maintenance/maintenance/article/14971137/proper-track-maintenance-for-compact-track-loaders
1 thought on “How to Change Skid Steer Tracks: A CTL Step-by-Step”
Comments are closed.